
MINE SITE APPLICATION
Mine Site Dust Suppression
Long-term dust control on tailings, exposed areas, batters and disturbed ground. These are the non-trafficked surfaces where repeat treatment stops paying for itself.
THE PROBLEM
Watering the same ground, week after week
On most operations, dust on non-trafficked surfaces is managed the way it has always been managed: a water cart, a circuit, and a result that lasts until the surface dries out again.
A treated surface holds between applications, so the same ground does not pull a water cart back every dry, windy period. That returns water, hours and plant availability to the rest of the operation. It also brings the areas that most need treatment into the programme: steep batters, soft ground and inactive faces.
Treating those surfaces properly once is usually cheaper than watering them all season.
WHAT WE TREAT
Non-trafficked mine site surfaces
Stockpiles
Product, ore and overburden stockpiles, including long-term and inactive piles where surface loss and dust lift-off are ongoing.
Exposed and disturbed ground
Cleared areas, laydowns, ROM surrounds, borrow pits and any surface stripped of cover and left open to wind.
Batters and steep faces
Embankments, dump faces and constructed slopes where getting a water cart on is either impractical or unsafe.
Inactive and legacy areas
Ground that is no longer operational but is still generating dust and still sitting inside your obligations.
Tailings storage facilities
Active and inactive tailings surfaces are a specialist case with their own constraints.
Pre-rehabilitation surfaces
Areas being held stable ahead of capping, revegetation or closure works.
SCOPE
We focus on what we know
Avrik specialises in non-trafficked surfaces. Haul roads, ramps and other running surfaces carry loads that break down a surface treatment, and they need a different approach, usually a road-specific binder programme run alongside your watering regime.
Where a site has both trafficked and non-trafficked ground, we treat the non-trafficked areas: stockpiles, batters, laydowns and inactive faces.
Stockpiles, batters and exposed ground
Non-trafficked surfaces treated without tying up a water cart or a crew.
HOW WE APPLY IT
Reach without driving on the surface
Product is mixed and pumped from application trucks on stable ground and carried to the treatment area by hose. The remotely operated UGV works the surface itself.
That combination is what makes the difficult areas treatable. Batters, soft ground and inactive faces stop being exceptions in the dust management plan and become part of the programme.
- Coverage. Typical daily coverage for UGV application is 20 hectares per day, with two operational personnel.
- Consistency. Controlled ground speed and application width produce an even film, which is what determines how long a treatment holds.
- Drift. Ground-based application close to the surface keeps product on target. Avrik rates wind sensitivity and product drift risk as very low.
- Record. Monitoring and aerial visibility give you evidence of what was treated and where.

TREATMENTS
Matching the product to the surface
Stockpiles, batters and exposed ground behave differently, and so should the treatment. Selection depends on the substrate, how exposed it is, how long the treatment has to hold and whether the area is heading toward rehabilitation.
- Polymer crust. Binds fine particles into a flexible crust on surfaces that stay undisturbed. Suits stockpiles and exposed ground.
- Fibre blanket. Holds on uneven or moving ground and in high salinity, and can carry seed where revegetation is the end point. Suits batters and pre-rehabilitation surfaces.
- Permeable crust. Binds the upper layer without sealing it, so air and water keep moving through and conditions underneath stay usable for germination. Suits ground heading toward rehabilitation.
- Your approved product. Where a product is already approved on site, we can apply that rather than introduce a new one.
Full detail on the products we apply is on the products page.
COMMON QUESTIONS
Mine site dust suppression FAQ
Can you treat haul roads?
No. Avrik applies treatments to non-trafficked surfaces. Haul roads and other running surfaces carry loads that break down a surface treatment and need a road-specific approach. Where a site has both, we treat the non-trafficked areas and leave the roads to a method built for them.
How does this compare to running a water cart?
Water controls dust on the day and stops working as the surface dries. A surface treatment binds the material so the area holds through dry and windy conditions, which takes that ground off the watering circuit and frees the cart, the water and the hours for somewhere else.
Can you get onto steep batters and soft ground?
That is the main reason the system exists. Product is supplied by hose from trucks on stable ground and applied by a remotely operated UGV, which runs interchangeable track systems and imposes as low as 2 psi, depending on track configuration. Treatment does not depend on driving a loaded water cart onto a slope or a soft surface. What the machine imposes is only part of the question. Whether a particular batter or soft area is workable is settled on the ground rather than from a specification, and we will tell you if it is not.
How long does a treatment last?
Treatment life depends on the product, the application rate, the surface and any subsequent disturbance from traffic, deposition or weather. Expected life and any re-treatment requirement are set out in the proposal rather than assumed.
How much area can you cover in a day?
Published typical daily coverage for UGV application is 20 hectares per day. Actual production depends on the treatment area and shape, product, application rate, hose runs and site access.
Can the treatment carry seed for rehabilitation?
Yes, where a fibre-based treatment suits the surface. Seed and fertiliser can be included so the area progresses toward vegetative cover while dust is controlled in the meantime.
Do you work on non-mining sites?
Yes. The same constraint applies on civil, industrial and infrastructure sites: large exposed surfaces, restricted access and dust obligations. Tell us the site and the surface and we will assess it the same way.
Start with a trial area
Pick a surface, we treat it, and you assess the result before committing to a programme.
DISCUSS YOUR PROJECT
Tell us about your site
Send through the detail below and we will come back with a proposed application approach, an indicative programme and the questions we still need answered.
- Site location and access. Where the site is and how the treatment areas can be reached.
- Surfaces and approximate area. Stockpiles, batters, exposed ground, and roughly how many hectares.
- The dust issue you are managing. What is being affected, and what has already been tried.
- Constraints. Water availability, ground conditions, exclusion zones, approvals.
- Timing. Seasonal window, shutdown, closure milestone or approval deadline.
Call (08) 8183 0300 or visit our contact page. See also the full range of dust suppression services. Prefer to run the equipment with your own crew? See dry hire.