
TREATMENT TYPE
Polymer Dust Suppression
Polymer treatments hold fine material in place through dry, windy conditions, ensuring zero dust lift-off
HOW IT WORKS
Binding the surface rather than wetting it
Water suppresses dust by weight. It works while the surface is damp and stops working when it dries, which on an exposed surface in summer can be the same afternoon.
A polymer treatment works differently. Applied as a dilute solution, the polymer binds fine particles to each other and to the surface, forming a continuous crust as it cures. The material is physically held rather than temporarily weighed down, so the treatment holds through dry conditions and wind rather than failing in them.
The crust is flexible rather than brittle. That matters, because a rigid surface cracks under thermal movement and settlement, and dust escapes through the cracks.
WHERE IT SUITS
Best on surfaces that stay put
Polymer is the right answer on non-trafficked surfaces that are not going to be disturbed during the treatment period.
Tailings and ash dams
Beaches, inactive cells and exposed tailings surfaces where the material is fine and readily mobilised.
Stockpiles
Product, ore and overburden stockpiles, particularly long-term and inactive piles.
Exposed and disturbed ground
Cleared areas, laydowns and any surface stripped of cover and left open to wind.
A crust that flexes instead of cracking
Applied at low concentration, binding fine particles into a surface that holds through wind and rain.
THE PRODUCT
SuppressX and HydroBond
Avrik applies two polymer treatments, and the question that separates them is whether anything has to grow.
On tailings, ash dams and process residues, the polymer is SuppressX, a dust suppressant for non-trafficked surfaces applied at low concentration.
- How it works. Cross-linked superabsorbent polymers bind fine particles into a continuous, flexible crust.
- Durability. The crust flexes rather than cracks, holding through strong wind and heavy rain events.
- Substrate. Non-toxic, and it does not alter the composition of the substrate it is applied to.
- Application. A single application controls dust lift-off, which makes the treatment cycle predictable.
- Surfaces. Tailings, ash dams, stockpiles and exposed ground.
HydroBond, where the ground has to grow something
A polymer and additive blend that penetrates and binds the upper layer into a hard crust. Both polymers work that way; the difference is what the bound layer then does. With SuppressX it is sealed and nothing passes through. With HydroBond it stays permeable, so air and water keep moving and dust is held while the surface stays able to germinate and establish cover.
It needs a substrate worth growing in, so it is not a tailings treatment. On tailings, ash and process residues, SuppressX or FibreLoc is the product.
Where a site already has an approved polymer product, we can apply that instead.
APPLICATION
The product is half the job
A polymer treatment performs as well as it is applied. Uneven coverage fails first at the thinnest points, and one thin patch pulls the whole area back into the re-treatment cycle.
- Even coverage. Controlled ground speed and application width produce a consistent film across the full area, not just the easy parts of it.
- Reaching the whole surface. Product is supplied by hose from trucks on stable ground and applied by a remotely operated UGV, so soft ground and steep faces are treated rather than skipped.
- Keeping product on target. Ground-based application close to the surface limits drift. Avrik rates product drift risk and wind sensitivity as very low.
- Not damaging what you just applied. Low surface disturbance matters when the thing you are protecting is a crust that has to cure.
- Evidence. Monitoring and aerial visibility give a record of what was treated and where.
COMMON QUESTIONS
Polymer dust suppression FAQ
What is polymer dust suppression?
A dilute polymer solution applied to a surface, which binds fine particles to each other and to the ground as it cures. The result is a flexible crust that holds the material in place through dry and windy conditions, rather than suppressing dust temporarily by wetting it.
How is it different from watering?
Water works by weight and only while the surface is damp. A polymer treatment physically binds the material, so it keeps working after the surface dries. In practice that means the treated area comes off the watering circuit for the life of the treatment.
Is polymer dust suppression safe for the environment?
SuppressX is made from non-toxic materials and does not alter the composition of the substrate it is applied to. Site-specific environmental approval requirements vary, and product documentation is provided as part of the proposal.
How long does a polymer treatment last?
Treatment life depends on the product, the application rate, the surface and any subsequent disturbance from traffic, deposition or weather. Expected life and any re-treatment requirement are set out in the proposal rather than assumed.
Can polymer be used on haul roads?
No. Trafficked surfaces break the crust under load. Haul roads need a road-specific binder programme run alongside watering, not a surface treatment.
What happens if it rains after application?
Once cured, the crust is built to resist heavy rain as well as wind. Timing of application relative to forecast rainfall is part of the treatment plan.
When would you recommend a fibre treatment instead?
Where the ground is uneven or moving, where revegetation is the end point, or where a saline surface has to stay held for a long period. A fibre blanket re-establishes itself after movement and can carry seed, which a polymer crust cannot.
Can you apply a product we have already approved?
Yes. Where a polymer product is already approved on your site, we can apply that rather than introduce a new one for approval.
Matched to the surface, not sold from a catalogue
DISCUSS YOUR PROJECT
Tell us about the surface
Send through the site, the surface and the period you need covered. We will recommend a treatment and an application approach.
Call (08) 8183 0300 or visit our contact page. See also the full range of dust suppression services, tailings dam dust suppression and mine site dust suppression.